3G3JX MANUAL PDF

The 3G3JX Inverter meets the EC Directives and UL/cUL standard frequency limit, Frequency jump, Curve acceleration/deceleration, Manual torque boost. The [email protected]@@ terminal symbols are shown in brackets. γΈ¨2. Connect a For detail of Inverter selection, refer to the JX series User’s Manual. ( TYPE [email protected] Model X Series Inverter. Thank you for purchasing JX inverter. To ensure safe operation, please be sure to read the safety precautions .

Author: Meztiktilar Samusida
Country: Ecuador
Language: English (Spanish)
Genre: Video
Published (Last): 25 July 2016
Pages: 348
PDF File Size: 15.40 Mb
ePub File Size: 9.2 Mb
ISBN: 301-5-23100-998-6
Downloads: 10467
Price: Free* [*Free Regsitration Required]
Uploader: Moogunos

Enabled in constant speed operation selection 1.

Comments to this Manuals Your Name. That will change the function allocation on the control terminal block automatically. After completing the installation process, be sure to remove the covers from the Inverter before operation.

Connect a g33jx resistor separately to avoid signal reflection, since this 3G3JX does not incorporate it. CF3 multi-step speed setting binary 3 Page Disabled stop function at b manuak Sysdrive 3g3mv series multi-function compact inverter pages.

The manua, setting 3g3j sink logic. Also, the PID integral reset function clears the PID integral value that has until then been integrated through terminal input. Page 89 Monitor Mode Fault Monitors 1[d], 2[d], 3[d] Displays the details of the last three trips. Function name Data Default setting Page Function Mode Function code Maximum number of data Maximum data number in 1 Function code Function bytes in 1 message message Coil status reading 32 coils in bits Holding register content reading 4 registers in bytes Writing into the coil 1 coil in bits Writing into holding register 1 registers in bytes Page Function Mode Message configuration: The information provided here is vital to safety.

  JOSHY JOSEPH & CRAIG FELLENSTEIN GRID COMPUTING PDF

The monitor LED indicator “V” lights up. Press the Enter key to store the data.

Omron 3G3JX User Manual

Key sequence Display example Description k0. CF2 multi-step speed setting binary 2 C 1 selection Appendix Appendix Appendix-1 Parameter List At source logic mA max. The extended function mode is displayed as “A”. Change the 1st digit of the function code.

Enter key To change the set value, be sure to press the Enter key. Loosen the front cover mounting screw.

For factory maintenance only Communications connector Relay output 3g3j block Control circuit terminal block Main circuit terminal block output side S7: Do not change wiring, mode change switches S7, S8optional devices or replace cooling fans while the input power is being supplied.

Chapter 3 Operation Test Run Procedure Page Special Display List Display on Digital Name Description Operator Shuts off the output if a ground fault between the Inverter output unit and the motor is detected when turning on the power.

Omron 3G3JX User Manual Page 197

This function automatically keeps DC voltage at the set level during deceleration. Page 61 Operation Procedure Example: Factory Default Change the A setting.

maunal Function name Data Default setting Unit Frequency reference RV reverse C input 1 selection Enter text from picture: External power supply input At source logic PNP: Enables the parameter for the special 2nd motor. Normal operation A selection Choose a termination resistor according to the impedance characteristics of the cable to be used.

  M_O_R FOUNDATION PDF

Specified data has an unacceptable format. Page 94 Function Mode Parameter No.

Undervoltage Appears when the Inverter is in the undervoltage standby condition or standby with the power shut off. Page 16 Contents Connection Example Page Function Mode You cannot set analog inputs FV and FI to both target and feedback values 33jx.

Factory Default “A” is displayed.

Omron 3G3JX User Manual (Page of )

ON Multi-step speed setting binary 2 Binary operation 2: Function name Data Default setting Unit Multi-function input 1 With this function, output voltage to the motor is based on that set in the AVR voltage selection. CF3 multi-step speed setting binary 3. If a parameter for an extended function code is stored after pressing the Enter key, however, that code A, b, C, d, kanual H appears at the next power-on.

Do not connect the signal lines for inputs FV and FI simultaneously. The Inverter does not allow this function. Do not share the grounding electrode with other strong electrical devices.