ASTM A/AM Direct No.: + Fax No.: + Email: [email protected] Board No.: + ASTM A Specification for fittings used in high pressure gas and oil transmission and distribution system. Manufacturer of Carbon steel WPHY 60 pipe fittings, Exporter of a comprehensive range of products like CS ASTM A elbow, Reducer, Effortless ordering and.
|Published (Last):||15 December 2004|
|PDF File Size:||18.68 Mb|
|ePub File Size:||12.5 Mb|
|Price:||Free* [*Free Regsitration Required]|
Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. After the removal of any cracksthe tees shall be re- examined by the removal of any Acceptable tees shall be marked with the symbol Astj or MTas applicableto indicate compliance. One or more of the supplementary requirements may be specified in the order.
The chemical composition thus determined. Failure to comply with the general requirements of Speci? The nickel content of the deposited weld metal shall not exceed 1.
Starting materials shall consist of plate, sheet, forgings, forging quality bar, and seamless or fusion-welded tubular products with filler metal added. Materials and Manufacture 5.
Specimens shall conform to required values of chemical composition and mechanical properties, namely: The purchaser may specify in the order a speci?
Combining values from the two systems may result in nonconformance with this specification. If you want to use it ,you can buy from following link: And over, Sizes tested Section;min. Full size Charpy, V-notch specimens shall be used whenever possible. The nickel content of the deposited weld metal. Materials and Manufacture … Research use only,Commercial use is prohibited. Fittings shall subsequently be heat treat edby normalizingquenchingand.
A860 WPHY 60 PIPE FITTTINGS
These fittings are for use in high-pressure gas and oil transmission and distribution systems. This area is de? This abstract is a brief summary of the referenced standard. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other.
How can I help you? Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Committee A01 has identi? Notch Toughness Properties 8. Other imperfections shall be treated in accordance with All base metal specimens shall be removed with the axis of the specimens longitudinal to the direction of primary metal?
Fittings formed above the transformation temperature or upon which welding is performed, shall be cooled to below the lower critical temperature prior to heat treatment. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.
One or more of the supplementary requirements may be specified in the order. Butt-welding fittings differing from these. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. In case of con?
The chemical composition shall conform to Table 1. The requirements are not intended to give assurance against fracture propagation. Link to Active This link will always route to the current Active version of the standard.
It aetm informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. When the section thickness lies between two values de? DIN Medium-weight threaded steel tubes. Fittings shall subsequently be heat treated by normalizing, quenching, and tempering or stress relieving in accordance with Speci? The results shall conform to Table 1 for either heat or Speci?
Electrodes for the shielded metal-arc process shall be of the low-hydrogen type. After the removal of any cracksthe tees shall be re.
ASTM A WPHY GR 60 Pipe Fittings, Carbon steel WPHY 60 buttweld fittings Manufacturer, Exporter.
Small size specimens shall be used only when the material thickness does not permit full size specimens. C These requirements are intended to minimize fracture initiation. The product analysis shall be the basis for rejection. Within the text, the SI units are shown in brackets. Only the ultimate tensile z860 need meet the minimum requirement of Table 2. The impact specimens shall not be?
Internal and qstm surface shall be examined when size permits permits accessibility. Materials shall be heat treated by normalizing, quenching, and tempering or stress relieving. A refers to the high yield strength of the fittings. NDE personnel shall be quali? The chemical composition thus determined shall conform to Table 1. All values are Maximum unless A range is stated.